18kg Stauf - MS Polymer Wood Flooring Adhesive

Product number 129130 Special features elastically deformable excess adhesive easy to remove very well spreadable particularly suitable for multiple layer wood flooring very good thread formation solvent-free, no hazard labels, water-free Suitable for installation of multiple layer wood flooring according to DIN EN 13489 Suitable subfloors concrete C 25 / 30 according to DIN 1045 (non-skid surface) calcium sulphate (flow) floors mastic asphalt screed, only after priming with STAUF VEP 195 STAUF levelling compounds for wood flooring chipboards (P4 to P7), OSB boards (OSB/2 to OSB/4) cement floors Suitable primers STAUF VDP 130 STAUF VPU 155 S STAUF VEP 195 STAUF WEP 180 Suitable levelling compounds STAUF XP 20 STAUF GS STAUF FZ STAUF XP 10 STAUF RM STAUF PU STAUF SSP RAPID Product properties aging-resistant suitable on subfloor heating systems ready for use no wood swelling not sensitive to frost very good thread formation very low emission fast setting Color beige Required quantities per m² 1150g with STAUF notched trowel no.5 Open time approx. 30 minutes at 20 °C Accessibility after approx. 24 hours Grinding/polishing: after 24 hours Room climate at work site Minimum 18 °C, maximum 75% rel. humidity, preferably max. 65% Storage requirements dry cool Shelf-life 12 months Giscode RS 10 Emicode EC1 plus Available Packaging 18 kg plastic bucket Examination of subfloor Prior to processing, the subfloor must be checked according to the standard DIN 18356 or corresponding national standards. The subfloor shall be resistant to pressure and tension, free of cracks, must have sufficient surface strength, be permanently dry, level, clean and free of from contaminants that may prevent adhesion, sinter layers etc. In addition, porosity and grip of surface need to be checked. Also check moisture content and absorption of subfloors as well as temperature, air humidity and subfloor temperature. Subfloor preparation It must be ensured that the subfloor is ready for installation by performing proper subfloor preparation, floors must be clean, have sufficient surface strength, must be level, permanently dry and free of cracks. A mechanical pretreatment of the subfloor (sweeping, vacuuming, mechanical brushing, sanding, milling, shot blasting) must be performed depending on type and condition of subfloor. Cracks and joints, except expansion joints and other construction joints, shall be solidly closed with STAUF repair resin and floor brackets. Cavities and indentations can be filled with a non self-levelling STAUF levelling compound. If necessary, make sure subfloors are level, have sufficient absorptive capacity and grip by applying the appropriate STAUF levelling compound. Processing Apply adhesive to sub floor using the appropriate STAUF notched trowel, avoid adhesive pooling and excessive layer thickness by evenly raking the notched trowel over adhesive layer. Install wood flooring during specified open time, slide in and press down firmly. In particular with raw wood flooring, avoided pushing adhesive into joints. Adhesive in joints can impair subsequent surface treatment. Depending on the degree of setting, adhesive residues can be removed with the appropriate STAUF cleaners. Please test the effect of the cleaner on the finish of the wood flooring in an inconspicuous area or on a sample prior to applying the cleaner. Hardened adhesive residues can easily be removed mechanically, mostly residue-free. However, longer exposures on finished wood flooring should be avoided to prevent possible contouring. Best for use at 18 - 25 °C, substrate temperature between 15 - 23 °C (with underfloor heating 18 - 22 °C) and relative humidity below 65 %, until the adhesive has set. Consumption varies depending on the surface, the back of the parquet or flooring, and the trowel teeth used. Adhering multiple layer wood flooring using a notched trowel STAUF No. 5 (TKB B9), or alternatively, large-format multiple layer parquet using STAUF No. 14. Accessibility Load bearing capacity depends on room climate and applied quantities of adhesive. Other information Plasticizers contained in the adhesive can cause flow asphalts to partially dissolve and may affect the wood flooring finish systems, especially for wood flooring installed without tongue and groove technique. The adhesive hardens when reacting with moisture either in the form of air humidity, wood or substrate moisture. The higher the ambient temperature, the faster the adhesive sets. Setting time increases with thickness of the adhesive layer. Adhesives classified as elastic according to DIN EN 14293 and ISO 17178, have elastic properties once hardened. On account of this elasticity, only minimal tension is transferred from parquet to sub floor, but dimensional changes of the parquet elements are allowed for. Limitation of liability The above information corresponds to the current state of development and practical experience. However, it is only intended to assist you in selecting our products and should be considered non-binding in all cases, as we have no influence on installation and installation requirements vary from place to place. Claims based on this information are therefore excluded. The same applies to the commercial and technical advisory service provided free of charge and without obligation. We would like to point out that the customer and installer must carry out sufficient tests themselves to ensure that the product is suitable for the intended use. With the publication of this information, all previous technical information (information sheets, installation recommendations and other information intended for similar purposes) loses its validity.